-40%
Hot Wire Foam Factory All Purpose Foam Coat 50lb #025ECO-50
$ 39.6
- Description
- Size Guide
Description
Fast ShippingMade in the USA
Quality Customer Service
Quality Foam Cutting Products Since 1991
All Purpose Foam Coat 50lb Protect Seal Hard Coat EPS XPS Styrofoam Polystyrene
Hot Wire Foam Factory
#025ECO-50
All Purpose Foam Coat
Proudly made in the USA!
Includes:
1 50lb Box of All Purpose Foam Coat
Details:
All purpose foam coat! This rock-hard cement-like coating protects and beautifies your foam projects. Comes in a dry powder - simply mix with water. It's tough but still sandable. It is inherently fire resistant. Can be used outdoors when sealed with any outdoor paint, or mixed with Boost liquid fortifier, or Bounce liquid rubberizer. Apply thick with a trowel or thin with a paintbrush. Sets up in only about 15 minutes. Extend the drying time by adding up to 50% latex paint with your water before mixing into the dry foam coat. Compatible with our Boost, Bounce, and Grit!
Features:
Adheres to polystyrene foams.
Forms a tough, protective surface.
Easy to mix. Just add water.
Use above or below grade.
Apply with paintbrush or trowel.
Paintable
Fireproof
Many decorative surface textures can be created.
Soap and water clean-up.
Add Boost fortifier if extra strength is desired.
Add Bounce for a rubbery, flexible surface texture.
INSTRUCTIONS:
MIXING:
Settling may occur in shipping causing a gritty texture that does not stick well. Remix if there is separation in dry mixture. Use when temperatures are between 40°F (4°C) and 100°F (38°C). Mix in a clean container with clean water. Add about 3 parts powder to 1 part water and mix until Foam Coat turns to a smooth paste. A drier mix is stronger. Do not overmix.
APPLYING:
If using extruded foam (ie Blueboard or Pinkboard) roughen surface with coarse sandpaper. Fill big cracks and holes by applying pasty mixture with a trowel. You may add more water until mixture is thin enough to apply with a paint brush, although thinning weakens coating. Can be applied with a standard spray hopper. Use thinned mixture to texture large areas. For best strength apply at least 1/4" (6mm) thick. Multiple coats may be applied. Try texturing surface before coating sets.
SET TIME:
Use within 30 minutes. Sets up in 1-3 hours. Fogging the surface for 24 hours will increase strength.
FINISHING:
Remove dust before painting. This product goes on rough and is not sandable. Finish as the surface is setting up.
CLEAN-UP:
Clean tools and brushes with clean soapy water before coating hardens.
WARNING:
Avoid prolonged contact with skin. Wear dust, skin and eye protection. Use approved respirator when sanding. In case of eye contact, flush immediately with water, consult a physician. Wash hands with soap and water after use and before eating. Keep out of reach of children.
COVERAGE 25lbs:
1/64” thick 288 sq ft
1/16” thick 72 sq ft
1/4” thick 18 sq ft
COMPRESSIVE STRENGTH:
ASTM C109
1 Day 750 psi
7 Day 2500 psi
28 Day 3500 psi
FLEXURAL STRENGTH:
ASTM C348
1 Day 350 psi
7 Day 550 psi
28 Day 1250 psi
FIRE DATA
Flammability: Noncombustible and not explosive.
Auto-ignition Temperature: Not Applicable
Flash Points: Not Applicable
PAYMENT
SHIPPING
WARRANTY & RETURNS
SUPPORT
PAYMENT
SHIPPING
WARRANTY & RETURNS
SUPPORT
We accept payment by any of the following methods:
PayPal Visa Amex Discover MasterCard
Buyers in California will be charged 7.75% sales tax.
Please pay as soon as possible after winning an auction, as that will allow us to ship your item to you sooner!
Packages are always insured. We ship within 2 business days (So if you order Monday, your order will ship by Wednesday). Weekends and holidays do not count as business days. We are not responsible for any customs fees, duties, taxes or tariffs imposed by the destination country which you may have to pay.
Customers in California will be charged a 7.75% sales tax.
USA
- FedEx & USPS (United States Postal Service)
Canada/Mexico
- USPS (United States Postal Service) International
Worldwide
(Except Hong Kong or China) - USPS (United States Postal Service) International
Please note, the 3" Knife WILL fit in a USPS Priority Mail Small Flat Rate Box for international orders, In order to fit your items in the box, the 3" Hot Knife will be put in the box very carefully with the blade slightly curved. Please remove the knife carefully from the box so as not to permanently bend or break the blade - it should readjust itself and go straight again.
Limited Warranty & Limitation of Liability Information:
This product is warranted for non-commercial use as follows: For 90 days from the original date of purchase, HWFF, Inc. will, at its option, repair or replace a defective unit free of
charge, if the unit is defective due to an original manufacturer’s defect. This warranty covers normal use and does not cover damage which occurs in shipment or unit failure which results from alteration, accident, misuse, abuse, or neglect. Except as herein expressly set forth, HWFF, Inc. shall not under any circumstances be responsible for any direct, indirect, incidental, or consequential damage resulting from the use of the equipment. The consumer’s sole remedy shall be such repair or replacement as expressly provided above.
Return Policy:
HWFF, Inc. retains the exclusive and sole right as to whether an item may be returned, exchanged, or order cancelled. HWFF, Inc. thus encourages customers to use caution when placing an order, as once placed the order cannot be cancelled, nor the item returned or exchanged unless HWFF, Inc. expressly consents. In order to obtain a refund or exchange, prior approval must be given by HWFF, Inc.. Please message us.
Generally, HWFF, Inc. will consider returns within thirty (30) days of purchase with a 20% restocking charge. Refunds are for the cost of product only; shipping and handling charges are not refundable. Buyer is responsible for return shipping. Please ask any questions you may have prior to buying.
Please send a message
(9AM-4PM, PST, Monday through Friday)
$Hot Wire Foam Factory #025ECO-50 All Purpose Foam Coat Proudly made in the USA! Includes: 1 50lb Box of All Purpose Foam Coat Details: All purpose foam coat! This rock-hard cement-like coating protects and beautifies your foam projects. Comes in a dry powder - simply mix with water. It's tough but still sandable. It is inherently fire resistant. Can be used outdoors when sealed with any outdoor paint, or mixed with Boost liquid fortifier, or Bounce liquid rubberizer. Apply thick with a trowel or thin with a paintbrush. Sets up in only about 15 minutes. Extend the drying time by adding up to 50% latex paint with your water before mixing into the dry foam coat. Compatible with our Boost, Bounce, and Grit! Features: Adheres to polystyrene foams. Forms a tough, protective surface. Easy to mix. Just add water. Use above or below grade. Apply with paintbrush or trowel. Paintable Fireproof Many decorative surface textures can be created. Soap and water clean-up. Add Boost fortifier if extra strength is desired. Add Bounce for a rubbery, flexible surface texture. INSTRUCTIONS: MIXING: Settling may occur in shipping causing a gritty texture that does not stick well. Remix if there is separation in dry mixture. Use when temperatures are between 40°F (4°C) and 100°F (38°C). Mix in a clean container with clean water. Add about 3 parts powder to 1 part water and mix until Foam Coat turns to a smooth paste. A drier mix is stronger. Do not overmix. APPLYING: If using extruded foam (ie Blueboard or Pinkboard) roughen surface with coarse sandpaper. Fill big cracks and holes by applying pasty mixture with a trowel. You may add more water until mixture is thin enough to apply with a paint brush, although thinning weakens coating. Can be applied with a standard spray hopper. Use thinned mixture to texture large areas. For best strength apply at least 1/4" (6mm) thick. Multiple coats may be applied. Try texturing surface before coating sets. SET TIME: Use within 30 minutes. Sets up in 1-3 hours. Fogging the surface for 24 hours will increase strength. FINISHING: Remove dust before painting. This product goes on rough and is not sandable. Finish as the surface is setting up. CLEAN-UP: Clean tools and brushes with clean soapy water before coating hardens. WARNING: Avoid prolonged contact with skin. Wear dust, skin and eye protection. Use approved respirator when sanding. In case of eye contact, flush immediately with water, consult a physician. Wash hands with soap and water after use and before eating. Keep out of reach of children. COVERAGE 25lbs: 1/64” thick 288 sq ft 1/16” thick 72 sq ft 1/4” thick 18 sq ft COMPRESSIVE STRENGTH: ASTM C109 1 Day 750 psi 7 Day 2500 psi 28 Day 3500 psi FLEXURAL STRENGTH: ASTM C348 1 Day 350 psi 7 Day 550 psi 28 Day 1250 psi FIRE DATA Flammability: Noncombustible and not explosive. Auto-ignition Temperature: Not Applicable Flash Points: Not Applicable
Quality Customer Service
Made in the USA
Fast Shipping
Quality Foam Cutting Products Since 1991
All Purpose Foam Coat 50lb Protect Seal Weatherproof Fire Resistant EPS XPS
Hot Wire Foam Factory
#025ECO-50
All Purpose Foam Coat
Proudly made in the USA!
Includes:
1 50lb Box of All Purpose Foam Coat
Details:
All purpose foam coat! This rock-hard cement-like coating protects and beautifies your foam projects. Comes in a dry powder - simply mix with water. It's tough but still sandable. It is inherently fire resistant. Can be used outdoors when sealed with any outdoor paint, or mixed with Boost liquid fortifier, or Bounce liquid rubberizer. Apply thick with a trowel or thin with a paintbrush. Sets up in only about 15 minutes. Extend the drying time by adding up to 50% latex paint with your water before mixing into the dry foam coat. Compatible with our Boost, Bounce, and Grit!
Features:
Adheres to polystyrene foams.
Forms a tough, protective surface.
Easy to mix. Just add water.
Use above or below grade.
Apply with paintbrush or trowel.
Paintable
Fireproof
Many decorative surface textures can be created.
Soap and water clean-up.
Add Boost fortifier if extra strength is desired.
Add Bounce for a rubbery, flexible surface texture.
INSTRUCTIONS:
MIXING:
Settling may occur in shipping causing a gritty texture that does not stick well. Remix if there is separation in dry mixture. Use when temperatures are between 40°F (4°C) and 100°F (38°C). Mix in a clean container with clean water. Add about 3 parts powder to 1 part water and mix until Foam Coat turns to a smooth paste. A drier mix is stronger. Do not overmix.
APPLYING:
If using extruded foam (ie Blueboard or Pinkboard) roughen surface with coarse sandpaper. Fill big cracks and holes by applying pasty mixture with a trowel. You may add more water until mixture is thin enough to apply with a paint brush, although thinning weakens coating. Can be applied with a standard spray hopper. Use thinned mixture to texture large areas. For best strength apply at least 1/4" (6mm) thick. Multiple coats may be applied. Try texturing surface before coating sets.
SET TIME:
Use within 30 minutes. Sets up in 1-3 hours. Fogging the surface for 24 hours will increase strength.
FINISHING:
Remove dust before painting. This product goes on rough and is not sandable. Finish as the surface is setting up.
CLEAN-UP:
Clean tools and brushes with clean soapy water before coating hardens.
WARNING:
Avoid prolonged contact with skin. Wear dust, skin and eye protection. Use approved respirator when sanding. In case of eye contact, flush immediately with water, consult a physician. Wash hands with soap and water after use and before eating. Keep out of reach of children.
COVERAGE 25lbs:
1/64” thick 288 sq ft
1/16” thick 72 sq ft
1/4” thick 18 sq ft
COMPRESSIVE STRENGTH:
ASTM C109
1 Day 750 psi
7 Day 2500 psi
28 Day 3500 psi
FLEXURAL STRENGTH:
ASTM C348
1 Day 350 psi
7 Day 550 psi
28 Day 1250 psi
FIRE DATA
Flammability: Noncombustible and not explosive.
Auto-ignition Temperature: Not Applicable
Flash Points: Not Applicable
PAYMENT
We accept payment by any of the following methods:
PayPal Visa Amex Discover MasterCard
Buyers in California will be charged 7.75% sales tax.
Please pay as soon as possible after winning an auction, as that will allow us to ship your item to you sooner!
SHIPPING
Packages are always insured. We ship within 2 business days (So if you order Monday, your order will ship by Wednesday). Weekends and holidays do not count as business days. We are not responsible for any customs fees, duties, taxes or tariffs imposed by the destination country which you may have to pay.
Customers in California will be charged a 7.75% sales tax.
USA
- FedEx & USPS (United States Postal Service)
Canada/Mexico
- USPS (United States Postal Service) International
Worldwide
(Except Hong Kong or China) - USPS (United States Postal Service) International
Please note, the 3" Knife WILL fit in a USPS Priority Mail Small Flat Rate Box for international orders, In order to fit your items in the box, the 3" Hot Knife will be put in the box very carefully with the blade slightly curved. Please remove the knife carefully from the box so as not to permanently bend or break the blade - it should readjust itself and go straight again.
WARRANTY & RETURNS
Limited Warranty & Limitation of Liability Information:
This product is warranted for non-commercial use as follows: For 90 days from the original date of purchase, HWFF, Inc. will, at its option, repair or replace a defective unit free of
charge, if the unit is defective due to an original manufacturer’s defect. This warranty covers normal use and does not cover damage which occurs in shipment or unit failure which results from alteration, accident, misuse, abuse, or neglect. Except as herein expressly set forth, HWFF, Inc. shall not under any circumstances be responsible for any direct, indirect, incidental, or consequential damage resulting from the use of the equipment. The consumer’s sole remedy shall be such repair or replacement as expressly provided above.
Return Policy:
HWFF, Inc. retains the exclusive and sole right as to whether an item may be returned, exchanged, or order cancelled. HWFF, Inc. thus encourages customers to use caution when placing an order, as once placed the order cannot be cancelled, nor the item returned or exchanged unless HWFF, Inc. expressly consents. In order to obtain a refund or exchange, prior approval must be given by HWFF, Inc.. Please message us.
Generally, HWFF, Inc. will consider returns within thirty (30) days of purchase with a 20% restocking charge. Refunds are for the cost of product only; shipping and handling charges are not refundable. Buyer is responsible for return shipping. Please ask any questions you may have prior to buying.
SUPPORT
Please send a message
(9AM-4PM, PST, Monday through Friday)
Hot Wire Foam Factory
#025ECO-50
All Purpose Foam Coat
Proudly made in the USA!
Includes:
1 50lb Box of All Purpose Foam Coat
Details:
All purpose foam coat! This rock-hard cement-like coating protects and beautifies your foam projects. Comes in a dry powder - simply mix with water. It's tough but still sandable. It is inherently fire resistant. Can be used outdoors when sealed with any outdoor paint, or mixed with Boost liquid fortifier, or Bounce liquid rubberizer. Apply thick with a trowel or thin with a paintbrush. Sets up in only about 15 minutes. Extend the drying time by adding up to 50% latex paint with your water before mixing into the dry foam coat. Compatible with our Boost, Bounce, and Grit!
Features:
Adheres to polystyrene foams.
Forms a tough, protective surface.
Easy to mix. Just add water.
Use above or below grade.
Apply with paintbrush or trowel.
Paintable
Fireproof
Many decorative surface textures can be created.
Soap and water clean-up.
Add Boost fortifier if extra strength is desired.
Add Bounce for a rubbery, flexible surface texture.
INSTRUCTIONS:
MIXING:
Settling may occur in shipping causing a gritty texture that does not stick well. Remix if there is separation in dry mixture. Use when temperatures are between 40°F (4°C) and 100°F (38°C). Mix in a clean container with clean water. Add about 3 parts powder to 1 part water and mix until Foam Coat turns to a smooth paste. A drier mix is stronger. Do not overmix.
APPLYING:
If using extruded foam (ie Blueboard or Pinkboard) roughen surface with coarse sandpaper. Fill big cracks and holes by applying pasty mixture with a trowel. You may add more water until mixture is thin enough to apply with a paint brush, although thinning weakens coating. Can be applied with a standard spray hopper. Use thinned mixture to texture large areas. For best strength apply at least 1/4" (6mm) thick. Multiple coats may be applied. Try texturing surface before coating sets.
SET TIME:
Use within 30 minutes. Sets up in 1-3 hours. Fogging the surface for 24 hours will increase strength.
FINISHING:
Remove dust before painting. This product goes on rough and is not sandable. Finish as the surface is setting up.
CLEAN-UP:
Clean tools and brushes with clean soapy water before coating hardens.
WARNING:
Avoid prolonged contact with skin. Wear dust, skin and eye protection. Use approved respirator when sanding. In case of eye contact, flush immediately with water, consult a physician. Wash hands with soap and water after use and before eating. Keep out of reach of children.
COVERAGE 25lbs:
1/64” thick 288 sq ft
1/16” thick 72 sq ft
1/4” thick 18 sq ft
COMPRESSIVE STRENGTH:
ASTM C109
1 Day 750 psi
7 Day 2500 psi
28 Day 3500 psi
FLEXURAL STRENGTH:
ASTM C348
1 Day 350 psi
7 Day 550 psi
28 Day 1250 psi
FIRE DATA
Flammability: Noncombustible and not explosive.
Auto-ignition Temperature: Not Applicable
Flash Points: Not Applicable